What Blast Media Should I Use In A Wet Blast Cabinet?

 




Introduction

Choosing the correct abrasive media for wet blasting is very important because an inappropriate media choice will not provide the desired finish. It can not only cause a rework but in some cases may cause damage to the blasted surface.

This article guides you in choosing the appropriate media for a wet blasting cabinet.

Different abrasive media that can be used in a wet blast cabinet

The different abrasive media that you normally use in a wet blast cabinet are garnet, glass bead, aluminum oxide, crushed glass, and soda bi-carbonate

  • Garnet (Almandine and Alluvial) : Garnet is a type of gemstone and has good natural abrasive properties. Garnet has a sub-angular shape, Mohs hardness number 7 to 7.5, comes in different grit sizes and it can remove coatings, old paint, rust, and mill scale from metal surfaces and can work on hard metals also. The coarser grit is suitable for working on aluminum, steel, stainless steel, and other metals and finer grit is suitable for materials like fiberglass. Garnet can quickly work through coatings and contaminants.
  • Crushed glass: Crushed glass has Mohs number of 5.5 to 7 and is good for wet blasting aluminum and steel. The crushed glass has an angular shape and forms a sharp anchor profile; however, selecting a proper grit size and blasting velocity can give you the required anchor profile/finish. The advantage of crushed glass is it is a recycled material (environmentally friendly), cheap, and effective for many works. Crushed glass can be an economical media for the wet blasting of components like alloy wheels.
  • Glass beads: A glass bead media consists of spherical glass particles and leaves a fine and polished finish on the blasted surface. The Mohs hardness of glass beads ranges from 5.5 to 6 and the particle size can be coarse to fine.The glass beads have a smooth surface all over and are safe for blasting soft and delicate materials. Glass beads are very popular for wet blast cabinets and by varying the blasting velocity a smooth anchored profile or a fine finish can be achieved.
  • Aluminum oxide: The aluminum oxide has angular shaped particles; a Mohs hardness of 8 to 9 and the grit size of this media can be coarse to fine depending on the need. By varying the grit size and blasting velocity, aluminum oxide can be used for wet blasting hard metals (even with thin sections) and this is a good media for tough cleaning, extracting paint, coating, and rust. This is useful for finishing and edge rounding of surfaces. The high recyclability of aluminum oxide makes it an affordable media.
  • Soda bi-carbonate: The soda bi-carbonate used for wet blasting is not the baking soda used in our kitchen. There are companies like Armex and Natrium that manufacture a variety of soda bi-carbonates specifically for the soda blasting process. The size of soda bi-carbonate particles may vary from 70 to 270 microns. Soda bi-carbonate is not an abrasive material and hence it cannot be used for surface profiling. Soda bi-carbonate is used as a media when the surface needs a smooth finish without any profile.
Location: 1k/18 Beafield Rd, Para Hills West SA 5096, Australia

Comments

Post a Comment

Popular posts from this blog

How to choose the best sandblasting equipment?

Image
  So, you want it smooth, you want it clean… We know this about you because you landed on this page. And here you’re going to find out exactly how to have it this way… your surface of course. You already know what you want to do with sandblasting. Sandblasting has been used over a hundred years to smooth a rough surface, shape a surface or remove surface contaminants and clean it. What you need in this process is abrasive material and a high pressure of air to stream it in the direction of the surface so you can remove paint, rust, dirt… and of course, the equipment to make it possible. Nowadays there is a wide range of sandblasting equipment in front of you. It can be confusing and hard to decide what equipment to choose by looking at the wide offer at first glance. Yet, with a little help from friends (us) making this decision can become a piece of cake. All you need is a focus on the right info. So, let’s get started. To choose the best sand blasting equipment you have to take...
Read more

Rust Inhibitor Dosing Unit - Installation Manual

Image
  Product Installation Choose the location: the water inlet and water outlet of the dosing unit must be in accordance with those of the main pipe. Dosing unit must be installed according to the method that the dosing unit is above the fluid intake tube. Fix the dosing unit to a wall or other facilities. Install the water inlet and outlet of the dosing unit according to the direction of water flow, to ensure its leak-proofness. (As shown in figure 2 and 3 below) Install 100-120 mesh screen between the inlets of water valve and dosing unit. When the addition of drugs is required, close the side branch valves of the dosing unit. The addition of drugs can be carried out when the valves on both sides of the dosing unit are opened. Crack sound will be heard when dosing unit begins to work. Currently, push the air vent valve on the top of the dosing unit and release the valve when small amount of water flows out. In this way, normal operation of doser can be ensured. ...
Read more

How do you prevent rusting while wet abrasive blasting?

Image
One of the most common question asked by people looking to purchase a dustless blasting machine is ‘How do I prevent steel from getting rusted after wet blasting? Yes, wet blasting can cause rust due to the water used in the process but it is easily preventable. The solution is quite simple using a Rust Inhibitor. Different rust inhibitors work in different ways. Whilst some removes chlorides from the water others provide an invisible film to the substrate.  There are over 200 different brands of Rust Inhibitor available in the market. Many coatings will not tolerate them, not all are environmentally friendly, and some are known carcinogens. Products include Holdtight 102 Blast x 108 RapidHold Superstrength The rust inhibitor is simply added to the pressure vessel in the recommended proportion using a dosing unit. Most rust inhibitors are required to be used in a ratio of 1:100 whereas the RapidHold Superstrength rust inhibitor is a concentrated solution requiring only 0.5% dosage ...
Read more